![]() Wiredraw cherrymax® ‘aB’ rivetsĬherryMAX® ‘AB’ rivets are shank expanding, locked-spindle, flush fracturing rivets meeting the requirements of NAS 1400 specification and conforming to NAS 1398/1399 ‘AB’ code standard pages, but offering non-shift tooling installation without changing pulling heads. The tools utilize one pulling head to install many diameters, head configurations and material combinations. CherryMAX® fasteners are currently available in 1/8″ through 1/4″ diameter in both nominal and 1/64″ oversize diameters. Each rivet is supplied with its own installation anvil which eliminates the problems resulting from worn anvils. CherryMAX® blind rivet system retains the large blind head of the Bulbed CherryLOCK® rivet. Simple to install.Bulbed CherryMAX® is a high stem retention lock spindle blind rivet with a visibly inspectable mechanical locking device. In addition, CherryMAX® was designed to be especially Provide a safe, strong, and reliable fastener for the aerospace Manufacturing methods, and quality testing in every CherryMAX® productĪre all part of the Cherry Aerospace "system" to Withstand the stresses found in aerospace structures. Rivet is a high-strength fastener specifically designed to What is the difference between CherryMAX® and the POP®-type rivets I can buy at my local That the rivet comes with the driving anvil above the rivet head to allow the use of single action tools. All materials, strengths, and features remain the same, except Located between the diameter number and the grip number. Is located in the part number as follows: NAS1398C4AB2. There is a code in the part number that calls out the CherryMAX® type fastener The CherryLOCK® "A" Code with an H955 series pulling head.Ĭan I order wiredraw CherryMAX® rivets to the NAS1398 and NAS1399 specifications? For example, a single action G746A tool will install Tooling with a special pulling head to seat the locking collar. The singleĪction CherryMAX® tools will, however, install the CherryLOCK® "A" Code fastener. Double action tools are the G784, and the G689 models with the H681 series pulling heads. Insert the locking collar of the CherryLOCK®. A double action tool must be used in order to The single action CherryMAX® tools will NOT pull the double action CherryLOCK® rivets. ![]() My CherryMAX® tools pull CherryLOCK® rivets? Model tool will pull the -4, -5, and -6 diameter CherryMAX® rivets Will my older CherryLOCK® tools pull CherryMAX® rivets? All of these tools have been used for many Right angle and offset tools are also available for this tool. It uses the H84A-8 pulling head for -8 diameter rivets, and the H701B-456 pulling head with 744-300 adapter for -4, This tool and the G704B power riveter will install -4,-5 and -6ĭiameter CherryMax rivets, using the H701B-456 straight, H753A-456 right angle or H782 offset pulling heads. The newest, smallest and lightest weight pneumatic tool is the G747. What power tool models should I use to install CherryMAX® rivets? What is the meaning of "456" on Cherry pulling heads? -456 indicates the the pulling head is capable of installing the 4 diameter (1/8"), 5 diameter (5/32") and 6 diameter (3/16") CherryMax rivets. Use only Cherry recommended tool systems with Cherry fasteners. Use of commercial riveting tools frequently results in poor aerospace fastener installations,Īnd may require removal of the fastener for replacement. These stems must have pulling serrations that match the serrations in the installation tool pulling heads ![]() To determine the minimum material thickness we subtract 1/16" - arrivingĬan I use commercially available installation tools to install Cherry aerospace fasteners?Ĭommercial riveting tools are designed to install softer stem, non-serrated commercial rivets.Ĭherry aerospace fasteners use hardened stems to meet the performance values required in the relevent procurement specifications. To further explain - 05 is 5/16" maximum material thckness. For example a CR rivet will have a material thickness or The typical industry accepted range between grip lengths are measured in 1/16" increments. ![]() How are grip lengths of blind rivets established? How are "diameters" of blind rivets measured? The term "diameter" refers to the nominal measurement of the rivet shank in 1/32", thus a 4 diameter rivet would be 4/32 or 1/8". I need further information on the Cherry® Rivetless Nut Plate?.Technical Support Frequently Asked Questions
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |